Your one-stop shop for all of your Radio needs!
Shipments will be delayed due to Hamvention. Thanks for understanding. We will be back on track and resume our speedy shipping on May 22nd.
We will be at Hamvention in Bldg 1 and also running the Alinco booth across from Comet in Bldg 3. Come see us.
Call us for the rebate program from RigExperts!
THANKS FOR SUPPORTING US!
SPECIAL ITEMS SHIPPING FREE ARE LOWER 48 ONLY! OTHERS PLEASE PHONE IN YOUR ORDERS!
Please PRAY for our Friends at RigExpert in Ukraine.
FREE SHIPPING ON MOST ORDERS OVER $100.00 IN THE LOWER 48 STATES.
WE SHIP TO ALL 50 STATES AND US TERRITORIES.
CANADIAN ORDERS PLEASE CALL FOR SHIPPING QUOTES.
HAVE QUESTIONS? CALL US 1-833-456-4673 TOLL FREE
The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 230 MHz.
A built-in ZOOM capability makes graphical measurements especially effective.
An integrated Time Domain Reflectometer mode can be used to locate a fault within the feedline system.
The following tasks are easily accomplished by using this analyzer:
Warranty coverage by the RigExpertCare™
Frequency range: 0.1 to 230 MHz
Frequency entry: 1 kHz resolution
Measurement for 25, 50, 75 and 100-Ohm systems
SWR measurement range: 1 to 100 in numerical modes,1 to 10 in chart modes
SWR display: numerical or analog indicator
R and X range: 0…10000, -10000…10000 in numerical modes,0…1000, -1000…1000 in chart modes
Display modes:– SWR at single or multiple frequencies– SWR, return loss, R, X, Z, L, C at single frequency– SWR chart, 20 to 500 points– R, X chart, 20 to 500 points– Smith chart, 20 to 500 points– Return loss chart, 20 to 500 points– TDR (Time Domain Reflectometer) chart– Cable tools (loss and characteristic impedance)
Optional open-short-load calibration.
Non Volatile memory:– 100 slots to save measurement results
RF output:– Connector type: N– Output signal shape: square– Output power: -10 dBm (at 50 Ohm load)
Power:– Four 1.5V alkaline batteries, type AAA– Max. 4 hours of continuous measurement, max. 2 days in stand-by mode when fully charged batteries are used– When the analyzer is connected to a PC or a DC adapter with USB socket, it takes power from these sources
Interface:– 290×220 color TFT display– 6×3 keys on the water-proof keypad– Multilingual menus and help screens– USB connection to a personal computer
Bluetooth specs.:Bluetooth Specification v.4.0 (BLE). Compatible with Android OS ver. 6.0 and higher. Analyzer AA-230 Zoom does not work through Bluetooth connection together with OS Windows and AntScope2.
Dimensions: 82 x 182 x 32 mm (3.2 x 7.2 x 1.3 in)
Operating temperature: 0…40 °C (32…104 °F)
Weight: 236 g (8.32 oz)
Warranty: 2 years
RigExpert AA-230 ZOOM is made in Ukraine.
Specifications are subject to change without notice.
The structure diagram of RigExpert AA-230 ZOOM is located below:
This is a diagram of the resistive bridge and its connection to the mixer:
Q: The output RF level at the antenna connector of the AA-230 ZOOM is -10 dBm, which is quite low compared to many other instruments. Does it mean the analyzer will not operate properly with long cables?
A: No, the AA-230 ZOOM will work fine with long (hundreds of meters) cables. The analyzer has a very sensitive, narrow band input, so -10 dBm is much enough for accurate measurements, even after loosing a few decibels in a long cable.
Q: The specs say the AA-230 ZOOM has a square wave output, which means there are several frequency components (harmonics) in such a signal. Then, how the SWR and other parameters of my antenna are measured at a specific, single frequency?A: Please look at the structure diagram of the analyzer. The instrument filters out all unnecessary frequency components, thanks to the very narrow band (several hundred Hz) filter.
Q: Is the AA-230 ZOOM sensitive to nearby repeaters or broadcast transmitters?A: No, unless a high-power transmitter is operating closely at the same frequency you are trying to use the analyzer at.
Q: Can I charge Ni-MH batteries inside the analyzer?A: No, please remove batteries from the analyzer and use a separate charger.
Q: Can I use Lithium-Ion batteries instead of alkaline or Ni-MH ones?A: Most likely, you will burn the analyzer. Lithium-Ion batteries have an output voltage of about 3.7 V each: compare to 1.2 V for Ni-MH and 1.5 V for alkaline ones.
AntScope2 for your PC on Windows or MacOS:
Flash Tool for Mac or Windows:
User’s & Software Manuals:
When I received my call sign a few years back, I was flooded with purchases of junk. Fast forward to 2019. I decided I wanted to build another option, not a dealer who has the same stuff as everyone else, but a dealer who actually uses what he sells. And that’s exactly what I do. If you see a product on this page or one of our tables at Hamfest, you can bet we have tried it and like it. From Radios to connectors we strive to bring you QUALITY. Sure, you can find it cheaper and we understand that, but if you don’t want to buy it again in 6 months, take a look at what we sell and have already approved. I am always just a phone call away. Jim Gifford, KM4MPF.
CALL US AT 1-833-4-KM4MPF / 1-833-456-4673 AND FIND OUT WHEN WE WILL BE AT A HAMFEST NEAR YOU.
4000 7th ave
Chattanooga, TN. 37407
9:00 till 4:00